質量問題二:新寶來發動機艙蓋開啟費力
部分新寶來出現發動機艙蓋開啟困難的現象,用操縱手柄開啟發動機艙蓋,發動機艙蓋沒有解鎖彈起(發動機艙蓋不能正常開啟)。經判定為發動機艙蓋鎖的質量問題或裝配質量問題,可能為下鎖體變形或者鎖鉤與下鎖體不對正,進而造成關閉開啟困難或假鎖。
對于此問題,廠家采取維修的方法進行解決。對輕微變形的發動機艙蓋鎖下鎖體不用更換,對于嚴重變形的必須更換。對于發動機艙蓋鎖假鎖現象,需要檢查下鎖體,看鎖鉤與下鎖體導槽位置是否對正。如果偏移較大,調整鎖體螺栓對正。如果對正后仍然出現功能故障(假鎖)情況,需用挫刀打磨鎖鉤兩側表面約0.3mm,然后用細砂紙打磨拋光并檢查開啟功能。最后將打磨過的鎖銷噴漆,防止氧化。
銆?a href="/common/footer/intro.shtml" target="_blank">鍏充簬鎴戜滑銆?銆? About us 銆? 銆?a href="/common/footer/contact.shtml" target="_blank">鑱旂郴鎴戜滑銆?銆?a target="_blank">騫垮憡鏈嶅姟銆?銆?a href="/common/footer/news-service.shtml" target="_blank">渚涚ǹ鏈嶅姟銆?/span>-銆?a href="/common/footer/law.shtml" target="_blank">娉曞緥澹版槑銆?銆?a target="_blank">鎷涜仒?shù)俊鎭?/font>銆?銆?a href="/common/footer/sitemap.shtml" target="_blank">緗戠珯鍦板浘銆?銆?a target="_blank">鐣欒█鍙嶉銆?/td> |
鏈綉绔欐墍鍒婅澆淇℃伅錛屼笉浠h〃涓柊紺懼拰涓柊緗戣鐐廣?鍒婄敤鏈綉绔欑ǹ浠訛紝鍔$粡涔﹂潰鎺堟潈銆?/font> |